RF RC M30
Wireless magnetic sensor
- Thermoplastic or stainless steel enclosure
- Power supply: Lithium battery
- sWave® wireless technology
RF Rx SW868-4S 24VDC Power-down-function
Wireless receiver
Material number: 1363011
- sWave® wireless technology
- 4 potential-free relay outputs
- 4 NO contacts, max. 3 A
- Transmitter/receiver assignment by teaching mode
- LEDs for indication of switching state
- SMA plug-in connector for external antenna
- Power-down-function (saves the last signal status from the relay output, if the power supply of the receiver box is interrupted)
Note
- External antenna always required for optimum wireless range
In stock
Contact
Technical data
| Applied standards | EN 60947-5-1; EN 61000-6-2, -6-3, -4-2, -4-20, EN 61000-4-4, -4-5, -4-6; EN 60068-2-6, EN 60068-2-27; EN 301 489-1; EN 301 489-3; EN 300 220-1; EN 300 220-2 |
|---|---|
| Number of channels | 4 |
| Mounting | DIN rail mounting |
| Connection | screw connection terminals 0.14 mm² - 2,5 mm², stripping length 8 mm |
| Degree of protection | IP 20 to IEC/EN 60529 |
| Inputs | 4 wireless channels, max. 40 transmitters |
| Outputs | 4 NO contacts (relay) |
| Rated operating current/voltage Ie/Ue | max. 0.1 A/24 VDC -15 % … +10 %; output contacts: 3 A/250 VAC; 3 A/24 VDC |
| Utilisation category | AC-15; DC-13 |
| Rated operating isolation voltage Ui | 250 VAC |
| Rated impulse withstand voltage Uimp | 2.5 kV |
| Frequency | 868.3 MHz (Europe) |
| Channel bandwidth | 480 kHz |
| Display | green LED: operating state, orange LED: switching conditions |
| Operation cycles | approx. 12000 telegrams with repetitions/h |
| Degree of pollution | 2 |
| Ambient temperature | 0 °C … +55 °C |
| Storage and shipping temperature | –25 °C … +85 °C |
| Note | Inductive loads (contactors, relays etc.) are to be suppressed by suitable circuitry. Switching contacts are not suitable for capacitive loads. |
| Wireless approvals | Europe: RED 2014/53/EU |
Downloads
Arrangement of receiver and switch antenna
Optimum Possible Unsuitable
mounting mounting mounting
Note
Magnetic base antennae must be mounted on a
metal plate of min. 250 x 250 mm size.
Accessories
RF magnet antenna 5dBi SMA plug-in connector straight 1.5 m
- Suitable for SW868, SW922 and EN868
- Cable length 1.5 m
- RF magnet antenna with straight SMA plug-in connector without ferrite core
RF magnet antenna 2dBi SMA plug-in connector straight 2 m
- Suitable for SW868 and EN868
- Cable length 2 m
- RF magnet antenna with straight SMA plug-in connector without ferrite core
RF SMA antenna socket 0.5 m
- RF SMA antenna socket with straight SMA plug-in connector
- Cable length 0.5 m
- Suitable for antennae with SMA plug-in connector
RF Magnet antenna 5dBi TNC plug-in connector IP 65 3.6 m
- Suitable for SW868 and EN868
- RF magnet antenna with straight TNC plug-in connector
- Cable length 3.6 m
RF SMA antenna socket 0.5 m with TNC plug-in connector IP 65
- RF SMA antenna socket with straight TNC plug-in connector
- Suitable for RF antenna 1275629
- Cable length 0.5 m
RF SMA antenna extension 3 m
- Plug on right side: straight SMA plug
- Socket on left side: straight SMA socket
- Suitable for EnOcean® as well as sWave® wireless technology
- Cable length 3 m
RF SMA antenna extension 5 m
- Plug on right side: straight SMA plug
- Socket on left side: straight SMA socket
- Suitable for EnOcean® as well as sWave® wireless technology
- Cable length 5 m
Power supply 24V DC
- Panel installation on mounting rails
- Service-friendly spring-loaded connector system
- Parallel connection option
- DC OK signalling via LEDs
- Stabilised and adjustable output voltage