RF RC M30 SW915 KST

Wireless magnetic sensor
Material number: 1362227
  • Thermoplastic enclosure
  • sWave® wireless technology
  • Power supply by Lithium battery
  • No wiring and pipe laying required
  • Easy programming of receiver
  • Output signal can be individually configurated at the receiver
Notes
  • 2 mounting nuts are included in delivery
  • The actuator is not included in the delivery of the switches
Contact

Technical data

Applied standards EN 60947-5-1, EN 61000-6-2, EN 61000-6-3, EN 61000-4-2, EN 301 489-1, EN 301 489-3, EN 300 220-1, EN 300 220-2
Enclosure PVC-C
Tightening torque mounting nut: max. 4 Nm
Degree of protection IP 67 to IEC/EN 60529
Protocol sWave®
Frequency 915 MHz (USA, Canada and Mexico)
Transmission power < 25 mW
Data rate 66 kbps
Channel bandwidth 550 kHz
Voltage supply lithium battery CR 2032 (replaceable)
System Lithium-MnO2
Nominal voltage 3 V
Nominal capacity 0.23 Ah
Type of installation flush, in not ferromagnetic material
Ambient temperature –25 °C … +65 °C
Switching system Reed contact
Switching distances M 100: sn = 15 mm;
M 30 Niro: sn = 30 mm
Hysteresis approx. 1 mm
Operation cycles approx. 12000 telegrams with repetitions/h
Current absorption without transmissions: approx. 1 μA
Wireless range max. 450 m outside,
max. 40 m inside
Mechanical life > 1 million operations
Actuating time min. 80 ms
Note Transmission of battery voltage and switching condition
Wireless approvals USA: FCC Part 15.247: XK5-RF Rx SW915
Canada: IC RSS-210: 5158A-RF Rx SW 915
Mexico: IFT - RCPSTRF17-1886
Weight 48 g

Downloads

Actuators

Type   Material no.  
Type    Material no.   
M 30 Niro stock type Standard versions, in stock or available at short notice 1189024
Type   Material no.  
Type    Material no.   
M 100 N stock type Standard versions, in stock or available at short notice 1042609

Accessories

Wireless receiver
RF Rx SW915-TCP/IP V2
  • sWave® wireless technology
  • Communication via UDP or TCP/IP (Server or Client - Mode)
  • Webserver based Setup
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of operating state
  • SMA reverse plug-in connector for external antenna
Wireless receiver / repeater
RF RxT SW915-USB
  • Different operating modes
  • USB-Standard Receiver Mode
  • USB Gateway Mode
  • Sniffer Mode
  • Repeater (1-Level and 2-Level Repeater Mode)
  • Virtual COM Port driver for Microsoft Windows, Linux, Apple Mac
Wireless receiver
RF Rx SW915-1W 24 VAC/DC
  • sWave® wireless technology
  • 1 potential-free relay output
  • 1 change-over contact, max. 6 A
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA reverse plug-in connector for external antenna
Wireless receiver
RF Rx SW915-2W-RS232 24 VAC/DC
  • sWave® wireless technology
  • 2 potential-free relay outputs
  • 2 change-over contacts, max. 6 A
  • RS 232 interface
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA reverse plug-in connector for external antenna
Wireless receiver
RF Rx SW915-4W 24 VAC/DC
  • sWave® wireless technology
  • 4 potential-free relay outputs
  • 4 change-over contacts
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA reverse plug-in connector for external antenna
Wireless receiver
RF Rx SW915-4S 24VDC - SET
  • sWave® wireless technology
  • 4 potential-free relay outputs
  • 4 NO contacts, max. 3 A
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA reverse plug-in connector for external antenna
Wireless receiver
RF Rx SW915-4S 24VDC Power-down-function
  • sWave® wireless technology
  • 4 potential-free relay outputs
  • 4 NO contacts, max. 3 A
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA reverse plug-in connector for external antenna
  • Power-down-function (saves the last signal status from the relay output, if the power supply of the receiver box is interrupted)
Wireless repeater
RF RxT SW915-1K
  • sWave® wireless technology
  • LEDs for indication of operating state
  • 1-level repeater: for the signal gain between transmitter and receiver
  • SMA reverse plug-in connector for external antenna
Wireless repeater
RF RxT SW915-2K
  • sWave® wireless technology
  • LEDs for indication of operating state
  • 1-level repeater: for the signal gain between transmitter and receiver
  • 2-level repeater: for the signal gain of one 1-level repeater
  • SMA reverse plug-in connector for external antenna
Power supply 24V DC
  • Stabilised and adjustable output voltage
  • DC OK signalling via LEDs
  • Parallel connection option
  • Push-in terminals
  • Panel installation on mounting rails
RF magnet antenna 5dBi R-SMA plug-in connector straight 3.6 m
  • RF magnet antenna with straight R-SMA plug-in connector without ferrite core
  • Suitable for SW915 and SW917
  • Cable length 3.6 m
RF magnet antenna 2dBi R-SMA plug-in connector straight 2 m
  • RF magnet antenna with straight R-SMA plug-in connector without ferrite core
  • Suitable for SW915 and SW917
  • Cable length 2 m
RF R-SMA antenna extension 3 m
  • Suitable for sWave® wireless technology
  • Cable length 3 m
  • Plug on left side: straight R-SMA plug
  • Socket on right side: straight R-SMA socket
RF R-SMA antenna extension 5 m
  • Suitable for sWave® wireless technology
  • Cable length 5 m
  • Plug on left side: straight R-SMA plug
  • Socket on right side: straight R-SMA socket
Field strength testing tool swView 915 MHz
  • Only suitable for sWave® 915 MHz wireless technology
  • Mobile field strength indicator for link range testing
  • To measure and indicate the electrical field strength
  • The batteries are included in delivery
  • Several functions can be selected: Scan-Mode, Repeat-Mode, Rescan-Mode, Radio-Link