RF RC M30 SW868 NIRO

Wireless magnetic sensor
Material number: 1363715
  • Stainless steel enclosure
  • sWave® wireless technology
  • Power supply by Lithium battery
  • No wiring and pipe laying required
  • Easy programming of receiver
  • Output signal can be individually configurated at the receiver
Notes
  • 2 mounting nuts are included in delivery
  • The actuator is not included in the delivery of the switches
Contact

Technical data

Applied standards EN 60947-5-1, EN 61000-6-2, EN 61000-6-3, EN 301 489-1, EN 301 489-3, EN 300 220-2
Enclosure stainless steel 1.4539
Tightening torque mounting nut: max. 75 Nm
Degree of protection IP 67 to IEC/EN 60529
Protocol sWave®
Frequency 868.3 MHz (Europe, China)
Transmission power < 25 mW
Data rate 66 kbps
Channel bandwidth 480 kHz
Voltage supply lithium battery CR 2032 (replaceable)
System Lithium-MnO2
Nominal voltage 3 V
Nominal capacity 0.23 Ah
Battery life depending on the switching frequency
sensor mainly not activated
10 s - 1.1 years; 100 s - 5.0 years; 1000 s - 7.6 years; without - 8.0 years
sensor mainly activated
10 s - 0.9 years; 100 s - 2.7 years; 1000 s - 3.4 years; without - 3.4 years
Type of installation flush, in not ferromagnetic material
Ambient temperature –20 °C … +65 °C
Switching system reed contact
Rated switching distance sn M 100: 15 mm; M 30 Niro: 30 mm
Hysteresis < 1 mm
Operation cycles max. 12000 telegrams with repetitions/h
Switching frequency max. 5 Hz
Standby current < 2 µA (< 5 µA activated)
Wireless range max. 450 m outdoors,
max. 40 m indoors
Mechanical life > 1 million operations
Actuating time min. 80 ms
Note status signal configurable ex works, transmission of battery voltage and switching condition
Wireless approvals Europe: RED 2014/53/EU
Weight 154 g

Downloads

Actuators

Type   Material no.  
Type    Material no.   
Actuating magnet M 30 Niro stock type Standard versions, in stock or available at short notice 1189024
Type   Material no.  
Type    Material no.   
Actuating magnet M 100 N stock type Standard versions, in stock or available at short notice 1042609

Accessories

Wireless receiver
RF Rx SW868-TCP/IP V2
  • sWave® wireless technology
  • Communication via UDP or TCP/IP (Server or Client - Mode)
  • Webserver based Setup
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of operating state
  • SMA plug-in connector for external antenna
Wireless receiver / repeater
RF RxT SW868-USB
  • Different operating modes
  • USB-Standard Receiver Mode
  • USB Gateway Mode
  • Sniffer Mode
  • Repeater (1-Level and 2-Level Repeater Mode)
  • Virtual COM Port driver for Microsoft Windows, Linux, Apple Mac
Wireless receiver
RF Rx SW868-1W 24 VAC/DC
  • sWave® wireless technology
  • 1 potential-free relay output
  • 1 change-over contact, max. 6 A
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA plug-in connector for external antenna
Wireless receiver
RF Rx SW868-2W-RS232 24 VAC/DC
  • sWave® wireless technology
  • 2 potential-free relay outputs
  • 2 change-over contacts, max. 6 A
  • RS 232 interface
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA plug-in connector for external antenna
Wireless receiver
RF Rx SW868-4W 24 VAC/DC
  • sWave® wireless technology
  • 4 potential-free relay outputs
  • 4 change-over contacts
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA plug-in connector for external antenna
Wireless receiver
RF Rx SW868-4S 24VDC - SET
  • sWave® wireless technology
  • 4 potential-free relay outputs
  • 4 NO contacts, max. 3 A
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA plug-in connector for external antenna
Wireless receiver
RF Rx SW868-4S 24VDC Power-down-function
  • sWave® wireless technology
  • 4 potential-free relay outputs
  • 4 NO contacts, max. 3 A
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA plug-in connector for external antenna
  • Power-down-function (saves the last signal status from the relay output, if the power supply of the receiver box is interrupted)
Wireless repeater
RF RxT SW868-1K
  • sWave® wireless technology
  • LEDs for indication of operating state
  • 1-level repeater: for the signal gain between transmitter and receiver
  • SMA plug-in connector for external antenna
Wireless repeater
RF RxT SW868-2K
  • sWave® wireless technology
  • LEDs for indication of operating state
  • 1-level repeater: for the signal gain between transmitter and receiver
  • 2-level repeater: for the signal gain of one 1-level repeater
  • SMA plug-in connector for external antenna
Power supply 24V DC
  • Stabilised and adjustable output voltage
  • DC OK signalling via LEDs
  • Parallel connection option
  • Push-in terminals
  • Panel installation on mounting rails
RF magnet antenna 5dBi SMA plug-in connector straight 1.5 m
  • RF magnet antenna with straight SMA plug-in connector without ferrite core
  • Suitable for SW868 and SW922
  • Cable length 1.5 m
RF magnet antenna 2dBi SMA plug-in connector straight 2 m
  • RF magnet antenna with straight SMA plug-in connector without ferrite core
  • Suitable for SW868 and SW922
  • Cable length 2 m
RF SMA antenna socket 0.5 m
  • Suitable for antennae with SMA plug-in connector
  • RF SMA antenna socket with straight SMA plug-in connector
  • Cable length 0.5 m
RF Magnet antenna 5dBi TNC plug-in connector IP 65 3.6 m
  • RF magnet antenna with straight TNC plug-in connector
  • Suitable for SW868
  • Cable length 3.6 m
RF SMA antenna socket 0.5 m with TNC plug-in connector IP 65
  • Suitable for RF antenna 1275629
  • RF SMA antenna socket with straight TNC plug-in connector
  • Cable length 0.5 m
RF SMA antenna extension 3 m
  • Suitable for sWave® wireless technology
  • Cable length 3 m
  • Plug on left side: straight SMA plug
  • Socket on right side: straight SMA socket
RF SMA antenna extension 5 m
  • Suitable for sWave® wireless technology
  • Cable length 5 m
  • Plug on left side: straight SMA plug
  • Socket on right side: straight SMA socket
Field strength testing tool swView 868 MHz
  • Only suitable for sWave® 868 MHz wireless technology
  • Mobile field strength indicator for link range testing
  • To measure and indicate the electrical field strength
  • The batteries are included in delivery
  • Several functions can be selected: Scan-Mode, Repeat-Mode, Rescan-Mode, Radio-Link
Lithium battery type CR 2032 (5 pieces)
  • Ordering unit: 5 pieces